Mitsubishi Raider C3378 Engine Trouble Code
What is Mitsubishi Raider C3378?
Mitsubishi Raider C3378 code can indicate a faulty oxygen sensor, which may eventually damage the catalytic converter (repair cost: $2,000–$2,200). Professional diagnosis costs around $200–$210. Oxygen sensors are often straightforward to replace — check your owner's manual for location and instructions. This issue should be addressed promptly to prevent further damage.
C3378 on the Mitsubishi Raider
On high-mileage Mitsubishi Raider examples, C3378 is often the first sign of a failing fuel pressure regulator. Residual fuel pressure bleeds off overnight, causing lean-start conditions that the ECU registers as a fault at the next cold start.
Code Information
| Code Type: | OBD-II Chassis (C) Trouble Code |
| System: | Chassis |
| Vehicle: | Mitsubishi Raider |
| Brand: | Mitsubishi |
| Model: | Raider |
| Code: | C3378 |
C3378 Mitsubishi Raider Symptoms
Check Engine Light
Illuminated Mitsubishi Raider dashboard warning
Engine Stalling
Engine stops unexpectedly or misfires
Performance Issues
Reduced power or acceleration on the Mitsubishi Raider
Starting Problems
Difficulty starting the engine
Poor Fuel Economy
Increased fuel consumption on the Mitsubishi Raider
Increased Emissions
Failed emissions test due to C3378
C3378 Code Structure
Understanding what each digit means in the C3378 chassis trouble code:
| C | 3 | 3 | 7 | 8 |
|---|---|---|---|---|
| Chassis Code | Ignition System Or Misfire | Throttle/Pedal Position Sensor/Switch A Circuit Intermittent | Cylinder 10 Contribution/Balance Fault | Clutch Position Sensor Circuit Malfunction |
How to Fix Mitsubishi Raider C3378
Diagnostic Steps:
Regarding C3378, carefully inspect the wire harness near the intake manifold bracket, best accessed from below near the oil filter. Look for chafing, pinching, or damaged insulation.
Repair Solution:
VSS concerns may stem from noisy input signals caused by RFI/EMI from ignition wires, charging circuits, or aftermarket equipment. Verify VSS reads 0 mph when transmission is in Park.
Technical Notes:
C3378 DTC specifically relates to camshaft timing. When cam timing is over-retarded, the check-engine light illuminates and this code sets. Verify VCT solenoid operation and check for contamination.
Mitsubishi Raider C3378 Repair Cost
ECU software update for the Mitsubishi Raider to resolve the C3378 calibration bug is performed free of charge at a franchised Mitsubishi dealer under the technical service bulletin programme. Always confirm the ECU part number and current flash version before spending money on sensors.
C3378 Description
C3378 engine trouble code is related to Clutch Position Sensor Circuit Malfunction.
Main Cause
The primary reason for C3378 OBD-II Engine Trouble Code is: Throttle/Pedal Position Sensor/Switch A Circuit Intermittent.
Common C3378 Misdiagnosis on the Mitsubishi Raider
On the Mitsubishi Raider, the VANOS (variable camshaft timing) solenoid is routinely replaced for C3378 when the actual issue is oil pressure insufficiency. No solenoid will operate correctly if the oil pressure required to actuate the VVT phaser is not present.
DIY Repair Guide: C3378 on Mitsubishi Raider
After any repair that involved disconnecting the battery on the Mitsubishi Raider, the power window, steering angle sensor, and transmission adaptive values all require a reset drive cycle. Skipping this can cause false fault codes — including C3378 — for the first two to three start cycles.
Preventing C3378 on the Mitsubishi Raider
Scheduled inspection of the Mitsubishi Raider air filter every 15,000 miles can prevent the intake restriction that leads to C3378. A blocked filter forces the engine to run rich, stressing the catalytic converter and ultimately storing fault codes.
Frequently Asked Questions — Mitsubishi Raider C3378
A: Yes. Some fault conditions, particularly those involving EVAP system leaks or marginal sensor readings, store codes without producing noticeable drivability symptoms. These are called memory faults and still need to be addressed because they will eventually cause performance issues.